WallWrap is a revolutionary digital wall graphic material with self adhesive backing that is flame resistant, repositionable and intended for short to mid term use of 1-2 years or more. Removal is as simple as peeling off the wall with no messy residue. The 11-15mil thickness, depending on the texture, hides wall imperfections adding to a professional finished look. Available in widths up to 54".
Longevity of 5-50 years indoors, depending on exposure to sunlight.
The heavy weight makes it very easy to install and it hides wall imperfections better than any other product. It comes in different textures.
The adhesive becomes more aggressive over time, so if it's left on for longer than 2-3 years, it will be more difficult to remove. If painted surfaces are not primed first, or if the paint doesn't have good adhesion to the wall, this will pull some paint off when it's removed. It's vinyl so it's not eco-friendly.
Wall graphics or murals that are easy to install. This product is our best at hiding imperfections in the wall.
|Is a Featured Product||No|
|Is Product Tiled?||Yes|
|Free Ground Shipping||No|
Wall Mural Images
Custom wallpaper murals can be printed from your own photo or design, or you can use a stock photo from one of the many sites available that provide images such https://www.istockphoto.com - https://www.shutterstock.com - https://www.dreamstime.com and many others. These sites have low cost stock images you can purchase, and there are some that offer free images, but make sure any free images are of a suitable resolution because you do often get what you pay for. If you plan on using your own file or photo, be sure you read the helpful information in the FAQ tab to learn about file sizing for quality wall mural printing. If you're printing a traditional wallpaper design with a repeating pattern, you can provide the pattern file and we can repeat it to fill your desired dimensions>
Removable self adhesive products will adhere to most clean, smooth surfaces. Desired results have been achieved on a variety of surfaces including but not limited to drywall, wood paneling, glass, metal, and composite board constructions. These products may not adhere properly to textured surfaces such as textured paints, textured wallpaper, cinder block or brick, outdoor walls, or any surface that is jagged or rough, so testing is required before installing on those surfaces. For best results we recommend dry wall that has been primed and painted (a white semi-gloss paint will promote the best adhesion and ease of removal). Please follow primer or paint instructions for application and optimal curing time prior to installing media. Painted walls that have not been primed are more likely to have the paint removed with the graphic. Testing of the paint adhesion is recommend prior to installation if this is a concern.
Prior to install, the panels should be rolled out flat and allowed to relax and reach room temperature. Recommended room acclimation time is 2 hours.
Make sure the surface is clean, smooth, dry, undamaged, free of mold, mildew, grease or stains, and structurally intact. If moisture is present, immediately identify and eliminate the source(s) of the moisture and verify that all wall surfaces are completely dry before proceeding. Any mold or mildew MUST be removed from walls and hanging surfaces prior to installation. Use a warm damp cloth to wipe off any dirt or dust and allow the surface to completely dry prior to installation. Do not use any chemicals to clean the intended surface. These products have been tested on many surfaces and should stick aggressively. They can be repositioned and re-applied as long as the adhesive surface has not been contaminated with dirt, dust, finger prints, etc. Drywall surfaces should be prepared with primer and paint, for best results we recommend a semi-gloss paint. If newly painted allow to dry for 30 days prior to installation.
Determine the starting point for the graphic. Small images could start from the right or left side, but we recommend larger graphics begin by installing the center panel first. Note: Use care to make sure the panels will cover full height and width of the project area. Some floors and ceilings are not square, so make sure the graphic covers the widest or tallest areas for the project.
Create a plum line on the wall with a pencil to create an edge guide for each panel.
For ease of handling, roll the first panel into a tight roll with printed image rolled inside. Now unroll 6" and peel back the liner paper 6". Cut away the unrolled portion of lining paper to expose the adhesive backing. Using the plum line, carefully align the top of your panel so that it is square from side to side, and the edge matches with your plumb line. Now the 6" that was exposed can be stuck against the wall surface.
With the top of the panel properly adhered to the wall, slowly peel the next foot or so of backing. Try to expose only a few feet of adhesive at a time to prevent unwanted sticking of the lower parts of your graphic. Work you way down the panel using a felt wrapped squeegee to carefully smooth the material onto the wall. We recommend using slow and even pressured side to side strokes, starting from the middle of the panel and moving outward to the sides. Once a few feet of material has been stuck to the wall, it should be possible to allow the remaining portion of the panel to drop to the floor. Now you can simply continue the procedure to easily progress down the wall.
When the entire panel has been positioned properly and smoothed, be sure to press down on the perimeter edge of each individual panel to assure good adhesion at the seams and edges. Any bubbles under the material should come out during the smoothing process. If necessary you can lift the material to release stubborn bubbles or large wrinkles.
Install remaining panels using the same method as above. Panel seams should overlap 1/2" using care to make sure of proper graphic alignment during installation. After all panels are installed, trim perimeter "bleed" around all edges using a sharp utility knife.
Removal should be as simple as pulling down from one corner. These products were designed to cleanly and easily be removed in complete panels. If the wall surface was prepared properly there will be no damage to drywall.
Ordinary dirt and smudges can be removed with a mild soap and warm water. Clean from bottom of wall upward. Rinse thoroughly with clean water from the top down using a sponge. Dry wallcovering with a soft lint free cloth or towel. For more difficult stains that are only surface deep, the use of a stronger detergent is recommended. Always test an inconspicuous area with the stronger detergent to be sure that the surface and ink are not damaged. DO NOT USE steel wool or powdered abrasive because they can damage the image and textured surface. DO NOT USE solvents, alcohol, pine oil, or cleaners that contain these kinds of products as they can remove the image and damage the textured surface. When cleaning, always take measures to prevent water from dripping behind molding.